Raspberry Pi Pico W (RP2040 + CYW43439)

The Raspberry Pi Pico W adds wireless communication capability to the standard Pico board by integrating an Infineon CYW43439 module.

Raspberry Pi Pico W

At a glance

Pins and properties exactly as the circuit editor and simulator define this part. The text below explains how to use them.

Board facts

Board facts
FactValue
Operating voltage3.3 V
FamilyRaspberry Pi
Python runtimemicropython
Wi-FiYes
BluetoothYes
Native USBYes

Pinout

Pinout of the Raspberry Pi Pico W. Select a label to see that pin in the table below.

The Raspberry Pi Pico W adds wireless communication capability to the standard Pico board by integrating an Infineon CYW43439 module.


1. Hardware Specifications

  • Processor: Dual-core ARM Cortex-M0+ running at 133 MHz.
  • Logic Level: 3.3V. All pins operate on 3.3V logic.
  • Memory Limits: 2 MB Flash, 264 KB SRAM.
  • Wireless: On-board 802.11n Wi-Fi (2.4 GHz) and Bluetooth v5.2 / BLE.

2. Detailed Pinout & GPIO Map (Wireless Pin Conflicts)

The Pico W shares the same form factor and general GP pin mappings as the standard Pico, but several internal GP lines are reserved for communicating with the CYW43439 wireless chip over a shared SPI bus:

Pins of this board
PinKindFeaturesAlternate functionsNotes
GP0GPIOPWMPWM, SDA, I2C, TX0, UART0General purpose pins mapped identically to the standard Pico.
GP1GPIOPWMPWM, SCL, I2C, RX0, UART0General purpose pins mapped identically to the standard Pico.
GNDGround
GP2GPIOPWMPWM, SDA, I2CGeneral purpose pins mapped identically to the standard Pico.
GP3GPIOPWMPWM, SCL, I2CGeneral purpose pins mapped identically to the standard Pico.
GP4GPIOPWMPWM, SDA, I2C, TX1, UART1General purpose pins mapped identically to the standard Pico.
GP5GPIOPWMPWM, SCL, I2C, RX1, UART1General purpose pins mapped identically to the standard Pico.
GNDGround
GP6GPIOPWMPWM, SDA, I2CGeneral purpose pins mapped identically to the standard Pico.
GP7GPIOPWMPWM, SCL, I2CGeneral purpose pins mapped identically to the standard Pico.
GP8GPIOPWMPWM, SDA, I2CGeneral purpose pins mapped identically to the standard Pico.
GP9GPIOPWMPWM, SCL, I2CGeneral purpose pins mapped identically to the standard Pico.
GNDGround
GP10GPIOPWMPWM, SDA, I2CGeneral purpose pins mapped identically to the standard Pico.
GP11GPIOPWMPWM, SCL, I2CGeneral purpose pins mapped identically to the standard Pico.
GP12GPIOPWMPWM, SDA, I2CGeneral purpose pins mapped identically to the standard Pico.
GP13GPIOPWMPWM, SCL, I2CGeneral purpose pins mapped identically to the standard Pico.
GNDGround
GP14GPIOPWMPWM, SDA, I2CGeneral purpose pins mapped identically to the standard Pico.
GP15GPIOPWMPWM, SCL, I2CGeneral purpose pins mapped identically to the standard Pico.
GP16GPIOPWMPWM, SDA, I2C, MISO, SPIGeneral purpose pins mapped identically to the standard Pico.
GP17GPIOPWMPWM, SCL, I2C, CS, SPIGeneral purpose pins mapped identically to the standard Pico.
GNDGround
GP18GPIOPWMPWM, SDA, I2C, SCK, SPIGeneral purpose pins mapped identically to the standard Pico.
GP19GPIOPWMPWM, SCL, I2C, MOSI, SPIGeneral purpose pins mapped identically to the standard Pico.
GP20GPIOPWMPWM, SDA, I2CGeneral purpose pins mapped identically to the standard Pico.
GP21GPIOPWMPWM, SCL, I2CGeneral purpose pins mapped identically to the standard Pico.
GNDGround
GP22GPIOPWMPWM, SDA, I2CGeneral purpose pins mapped identically to the standard Pico.
RUNSpecialRESET
GP26GPIOPWM, ADCPWM, SDA, I2C, ADC012-bit ADC channel (values 0–4095).
GP27GPIOPWM, ADCPWM, SCL, I2C, ADC112-bit ADC channel (values 0–4095).
GNDGround
GP28GPIOPWM, ADCPWM, SDA, I2C, ADC212-bit ADC channel (values 0–4095).
ADC_VREFAnalogADC, Input onlyNot a usable analog input — a reference pin only.
3V3Power3.3V
3V3_ENSpecialPull low to disable the onboard regulator.
GNDGround
VSYSPower
VBUSPower5V
  • WL_GPIO 0: Connected directly to the CYW43439 wireless chip, not an RP2040 GPIO at all. Toggled via the board_builtin_led block.

[!NOTE] GP23, GP24, GP25, and GP29 aren't wireable pins in OMS at all — same as the plain Pico (Section 3.12), they don't appear in the simulator's pin list. On real hardware GP23/24 talk to the CYW43439 over an internal SPI bus and GP29 monitors VSYS — none of that is exposed as a header pin you could accidentally wire in OMS.


3. Power Architecture & Wireless LED

Because the onboard LED is relocated to the wireless chip, writing directly to a plain GPIO number won't toggle it. OMS's board_builtin_led block generates the exact same code here as on the plain Pico — digitalWrite(LED_BUILTIN, ...) — relying on the underlying Arduino-Pico board package (not anything OMS's own code generator special-cases) to correctly route LED_BUILTIN through the CYW43439 driver on this specific board variant.

  • Power: Powering from USB provides 5V. Ensure stable current supply, as Wi-Fi transmission bursts can trigger brownouts if powered via thin cables.

4. Compiler Settings & IDE Properties

When targeting this board, the compiler utilizes the following parameters:

  • FQBN: rp2040:rp2040:rpipicow
  • Default Flashing Baud Rate: 115200
  • Flash Mode / File Type: uf2
  • Flash Memory Offsets: { bootloader: 0x0000, partitions: 0x0000, app: 0x0000 }
  • Programming Runtimes: Supports C++ (Arduino) and MicroPython.

5. Supported Blockly Board Blocks

Drawing the blocks…

6. Simulator and Flashing Diagnostics

  • Simulator: Core timers, digital GPIOs, and the onboard LED toggle visually on the canvas. Wi-Fi connections are bypassed in simulation.
  • Flashing Guide: Same as the standard Pico. Disconnect USB, hold the physical BOOTSEL button, reconnect USB, release BOOTSEL, and drag/drop the compiled .uf2 binary to the RPI-RP2 drive. If MicroPython is active, OMS flashes updates directly over Web Serial without requiring BOOTSEL resets.

7. Communication Buses & Electrical Capabilities

Beyond the per-pin table above, here's the board's bus-level capability summary (from its own capabilities config) — identical to the plain Pico (Section 3.12):

BusDetails
UART2 hardware buses — UART0 (TX=GP0, RX=GP1) and UART1 (TX=GP4, RX=GP5).
I2CDefault on GP4 (SDA) / GP5 (SCL) — shared with UART1's pins; pick one bus or the other per project.
SPIDefault on MOSI GP19, MISO GP16, SCK GP18, CS GP17.
1-WireNo dedicated 1-Wire hardware peripheral. Sensors like the DHT11 bit-bang the timing on any regular digital pin instead.
Analog (ADC)3 ADC-capable pins (GP26–GP28), 12-bit resolution. No hardware DAC, no touch.
PWMEvery GPIO pin is PWM-capable (16 channels total), 16-bit resolution, up to 125 MHz.

Electrical limits: max 12 mA per pin, max 300 mA total across all pins combined.


8. Further Reading


Raspberry Pi Pico W (RP2040 + CYW43439) — OMS Parts