Raspberry Pi Pico 2 (RP2350)

The Raspberry Pi Pico 2 is the next-generation Pico board, powered by Raspberry Pi’s new RP2350 microcontroller chip, offering significantly faster cores and double the memory capacity.

Raspberry Pi Pico 2

At a glance

Pins and properties exactly as the circuit editor and simulator define this part. The text below explains how to use them.

Board facts

Board facts
FactValue
Operating voltage3.3 V
FamilyRaspberry Pi
Python runtimemicropython
Wi-FiNo
BluetoothNo
Native USBYes

Pinout

Pinout of the Raspberry Pi Pico 2. Select a label to see that pin in the table below.

The Raspberry Pi Pico 2 is the next-generation Pico board, powered by Raspberry Pi’s new RP2350 microcontroller chip, offering significantly faster cores and double the memory capacity.


1. Hardware Specifications

  • Processor: Dual-core ARM Cortex-M33 running at 150 MHz. (The RP2350 silicon also contains dual Hazard3 RISC-V cores, selectable at the factory/OTP level — see the note in Section 3 about what OMS itself actually exposes.)
  • Logic Level: 3.3V. All pins operate on 3.3V logic.
  • Memory Limits: 4 MB Flash, 520 KB SRAM (double the RP2040's SRAM).
  • Wireless: None (wired USB connections only).

2. Detailed Pinout & GPIO Map

The RP2350 chip's silicon supports a flexible GPIO function mux, but like the original Pico (Section 3.12), OMS's simulator only implements one fixed default pin per bus — it does not model the chip's full alternate-function flexibility. The table below reflects what's actually wired in OMS, not the chip datasheet's full mux table:

Pins of this board
PinKindFeaturesAlternate functionsNotes
GP0GPIOPWMPWM, SDA, I2C, TX0, UART0Default UART0 Serial Transmit.
GP1GPIOPWMPWM, SCL, I2C, RX0, UART0Default UART0 Serial Receive.
GNDGround
GP2GPIOPWMPWM, SDA, I2CGeneral Purpose Input/Output.
GP3GPIOPWMPWM, SCL, I2CGeneral Purpose Input/Output.
GP4GPIOPWMPWM, SDA, I2C, TX1, UART1Default I2C data line; secondary UART transmit.
GP5GPIOPWMPWM, SCL, I2C, RX1, UART1Default I2C clock line; secondary UART receive.
GNDGround
GP6GPIOPWMPWM, SDA, I2CGeneral Purpose Input/Output (no fixed bus role in OMS).
GP7GPIOPWMPWM, SCL, I2CGeneral Purpose Input/Output (no fixed bus role in OMS).
GP8GPIOPWMPWM, SDA, I2CGeneral Purpose Input/Output (no fixed bus role in OMS).
GP9GPIOPWMPWM, SCL, I2CGeneral Purpose Input/Output (no fixed bus role in OMS).
GNDGround
GP10GPIOPWMPWM, SDA, I2CGeneral Purpose Input/Output (no fixed bus role in OMS).
GP11GPIOPWMPWM, SCL, I2CGeneral Purpose Input/Output (no fixed bus role in OMS).
GP12GPIOPWMPWM, SDA, I2CGeneral Purpose Input/Output (no fixed bus role in OMS).
GP13GPIOPWMPWM, SCL, I2CGeneral Purpose Input/Output (no fixed bus role in OMS).
GNDGround
GP14GPIOPWMPWM, SDA, I2CGeneral Purpose Input/Output (no fixed bus role in OMS).
GP15GPIOPWMPWM, SCL, I2CGeneral Purpose Input/Output (no fixed bus role in OMS).
GP16GPIOPWMPWM, SDA, I2C, MISO, SPIDefault SPI data-in line.
GP17GPIOPWMPWM, SCL, I2C, CS, SPIDefault SPI chip-select line.
GNDGround
GP18GPIOPWMPWM, SDA, I2C, SCK, SPIDefault SPI clock line.
GP19GPIOPWMPWM, SCL, I2C, MOSI, SPIDefault SPI data-out line.
GP20GPIOPWMPWM, SDA, I2CGeneral Purpose Input/Output.
GP21GPIOPWMPWM, SCL, I2CGeneral Purpose Input/Output.
GNDGround
GP22GPIOPWMPWM, SDA, I2CGeneral Purpose Input/Output.
RUNSpecialRESETPull low to reset the RP2350 chip.
GP26GPIOPWM, ADCPWM, SDA, I2C, ADC012-bit ADC channel (values 0–4095).
GP27GPIOPWM, ADCPWM, SCL, I2C, ADC112-bit ADC channel (values 0–4095).
GNDGround
GP28GPIOPWM, ADCPWM, SDA, I2C, ADC212-bit ADC channel (values 0–4095).
ADC_VREFAnalogADC, Input only
3V3Power3.3V
3V3_ENSpecial
GNDGround
VSYSPower
VBUSPower5V

Not simulated in OMS: GP23 (SMPS power-save mode), GP24 (VBUS sense), and GP29 (internal VSYS monitor) are internal-only lines on real RP2350 silicon, and OMS's board definition doesn't expose them as wireable pins at all — they're absent from the pinout entirely, not just restricted. GP25 is also not a general-purpose wireable pin here — it only exists as the synthetic pin the onboard diagnostic LED is linked to (via board_builtin_led, Section 5 below), the same pattern used for the LED pin on every other board in this catalog.


3. Core Architecture & PIO

  • Cortex-M33 vs. Hazard3 RISC-V: The RP2350 chip genuinely contains both a dual-core ARM Cortex-M33 pair and a dual-core Hazard3 RISC-V pair, selectable via the chip's own OTP configuration at the hardware level. OMS does not expose a RISC-V toggle anywhere — every project compiles for this board against the fixed rp2040:rp2040:rpipico2 FQBN (Section 4 below), which targets the Cortex-M33 side only. There is no "advanced project properties" option to switch cores in OMS today.
  • PIO (Programmable I/O): The RP2350 silicon does have 3 PIO blocks of 4 state machines each (12 total, vs. RP2040's 8) — real background info about the chip. OMS has no PIO support in Blockly or the simulator at all, on this board or any RP2040/RP2350-family board — there is no pico_pio_init/pico_pio_write-style block anywhere in the codebase. Using PIO requires ejecting to hand-written C++ outside OMS.

4. Compiler Settings & IDE Properties

When targeting this board, the compiler utilizes the following parameters:

  • FQBN: rp2040:rp2040:rpipico2
  • Default Flashing Baud Rate: 115200
  • Flash Mode / File Type: uf2
  • Flash Memory Offsets: { bootloader: 0x0000, partitions: 0x0000, app: 0x0000 }
  • Programming Runtimes: Supports C++ (Arduino) and MicroPython.

5. Supported Blockly Board Blocks

Drawing the blocks…

6. Simulator and Flashing Diagnostics

  • Simulator: Unlike the original Pico/Pico W (which run on the real rp2040js instruction-set simulator), the Pico 2 runs on OMS's micropython-wasm engine — there is no cycle-accurate RP2350 instruction-set emulator in OMS. Standard digital/analog/PWM functions and board LEDs are modeled, but core-level behavior (M33 vs. RISC-V, secure boot, PIO registers) isn't simulated at the instruction level at all — it isn't a matter of "bypassing" fine-grained emulation, there simply isn't a chip-level emulator for this board the way there is for AVR or the original RP2040 Pico.
  • Flashing Guide:
    1. Unplug the USB cable from the Pico 2.
    2. Press and hold the white BOOTSEL button.
    3. Reconnect the USB cable, then release BOOTSEL.
    4. The board mounts on your computer as a storage drive named RPI-RP2.
    5. Click Flash in OMS. The IDE compiles and saves the .uf2 file directly to the drive, which auto-unmounts and launches your code.

7. Communication Buses & Electrical Capabilities

Beyond the per-pin table above, here's the board's bus-level capability summary (from its own capabilities config):

BusDetails
UART2 hardware buses — UART0 on GP0(TX)/GP1(RX), UART1 on GP4(TX)/GP5(RX).
I2CDefault bus on GP4 (SDA) / GP5 (SCL).
SPIDefault bus: MISO GP16, CS GP17, SCK GP18, MOSI GP19.
1-WireNo dedicated 1-Wire hardware peripheral on this chip — sensors like the DHT11 are supported by bit-banging the protocol on any regular digital pin.
Analog (ADC)3 channels (GP26–GP28), 12-bit resolution (0–4095), no hardware DAC.
PWMAvailable on every GPIO pin, up to 150 MHz clk_sys-derived timing.

Electrical limits: max 12 mA per pin, max 300 mA total across all pins combined. Operating voltage range 1.62V–3.63V, nominal 3.3V.


8. Further Reading


Raspberry Pi Pico 2 (RP2350) — OMS Parts