Raspberry Pi Pico 2W (RP2350 + CYW43439)

The Raspberry Pi Pico 2W combines the high-performance dual-core RP2350 microcontroller with the CYW43439 wireless module, representing the most powerful board in the Pico family.

Raspberry Pi Pico 2W

At a glance

Pins and properties exactly as the circuit editor and simulator define this part. The text below explains how to use them.

Board facts

Board facts
FactValue
Operating voltage3.3 V
FamilyRaspberry Pi
Python runtimemicropython
Wi-FiYes
BluetoothYes
Native USBYes

Pinout

Pinout of the Raspberry Pi Pico 2W. Select a label to see that pin in the table below.

The Raspberry Pi Pico 2W combines the high-performance dual-core RP2350 microcontroller with the CYW43439 wireless module, representing the most powerful board in the Pico family.


1. Hardware Specifications

  • Processor: Dual-core ARM Cortex-M33 running at 150 MHz. (The RP2350 silicon also contains dual Hazard3 RISC-V cores, selectable at the factory/OTP level — see Section 3.14's note on what OMS itself actually exposes for compiling; the same applies here.)
  • Logic Level: 3.3V. All pins operate on 3.3V logic.
  • Memory Limits: 4 MB Flash, 520 KB SRAM.
  • Wireless: Onboard Wi-Fi (802.11n, 2.4 GHz) and Bluetooth v5.2 / BLE, via the same CYW43439 module used on the original Pico W.

2. Detailed Pinout & GPIO Map

The Pico 2W shares the exact same GPIO layout and CYW43439 bus-conflict pins as the Pico 2 (Section 3.14) — same fixed OMS bus defaults, same GP23/GP24/GP25/GP29 caveats. As with every other Pico-family board, OMS's simulator only implements one fixed default pin per bus, not the chip's full alternate-function mux:

Pins of this board
PinKindFeaturesAlternate functionsNotes
GP0GPIOPWMPWM, SDA, I2C, TX0, UART0Default UART0 Serial Transmit.
GP1GPIOPWMPWM, SCL, I2C, RX0, UART0Default UART0 Serial Receive.
GNDGround
GP2GPIOPWMPWM, SDA, I2CGeneral Purpose Input/Output.
GP3GPIOPWMPWM, SCL, I2CGeneral Purpose Input/Output.
GP4GPIOPWMPWM, SDA, I2C, TX1, UART1Default I2C data line; secondary UART transmit.
GP5GPIOPWMPWM, SCL, I2C, RX1, UART1Default I2C clock line; secondary UART receive.
GNDGround
GP6GPIOPWMPWM, SDA, I2CGeneral Purpose Input/Output (no fixed bus role in OMS).
GP7GPIOPWMPWM, SCL, I2CGeneral Purpose Input/Output (no fixed bus role in OMS).
GP8GPIOPWMPWM, SDA, I2CGeneral Purpose Input/Output (no fixed bus role in OMS).
GP9GPIOPWMPWM, SCL, I2CGeneral Purpose Input/Output (no fixed bus role in OMS).
GNDGround
GP10GPIOPWMPWM, SDA, I2CGeneral Purpose Input/Output (no fixed bus role in OMS).
GP11GPIOPWMPWM, SCL, I2CGeneral Purpose Input/Output (no fixed bus role in OMS).
GP12GPIOPWMPWM, SDA, I2CGeneral Purpose Input/Output (no fixed bus role in OMS).
GP13GPIOPWMPWM, SCL, I2CGeneral Purpose Input/Output (no fixed bus role in OMS).
GNDGround
GP14GPIOPWMPWM, SDA, I2CGeneral Purpose Input/Output (no fixed bus role in OMS).
GP15GPIOPWMPWM, SCL, I2CGeneral Purpose Input/Output (no fixed bus role in OMS).
GP16GPIOPWMPWM, SDA, I2C, MISO, SPIDefault SPI data-in line.
GP17GPIOPWMPWM, SCL, I2C, CS, SPIDefault SPI chip-select line.
GNDGround
GP18GPIOPWMPWM, SDA, I2C, SCK, SPIDefault SPI clock line.
GP19GPIOPWMPWM, SCL, I2C, MOSI, SPIDefault SPI data-out line.
GP20GPIOPWMPWM, SDA, I2CGeneral Purpose Input/Output.
GP21GPIOPWMPWM, SCL, I2CGeneral Purpose Input/Output.
GNDGround
GP22GPIOPWMPWM, SDA, I2CGeneral Purpose Input/Output.
RUNSpecialRESETPull low to reset the RP2350 chip.
GP26GPIOPWM, ADCPWM, SDA, I2C, ADC012-bit ADC channel (values 0–4095).
GP27GPIOPWM, ADCPWM, SCL, I2C, ADC112-bit ADC channel (values 0–4095).
GNDGround
GP28GPIOPWM, ADCPWM, SDA, I2C, ADC212-bit ADC channel (values 0–4095).
ADC_VREFAnalogADC, Input only
3V3Power3.3V
3V3_ENSpecial
GNDGround
VSYSPower
VBUSPower5V

Not simulated in OMS: GP23 (wireless power-save), GP24 (CYW43439 SPI data line), and GP29 (internal VSYS monitor) are internal-only lines used by the wireless module or chip on real hardware, and OMS's board definition doesn't expose them as wireable pins at all — they're absent from pins[] entirely, not just restricted. GP25 genuinely isn't connected to the onboard LED here — correct in the original text — the LED is instead wired to a synthetic WL_GPIO0 pin (CYW43439-driven), toggled the same way as the original Pico W via board_builtin_led (Section 5 below).


3. Core Architecture & PIO

Same silicon and same OMS-side limitations as the plain Pico 2 (Section 3.14): the RP2350 chip has switchable Cortex-M33/Hazard3-RISC-V cores and 12 PIO state machines at the hardware level, but OMS exposes neither — every project compiles against the fixed rp2040:rp2040:rpipico2w FQBN (Cortex-M33 only, no RISC-V toggle in project settings), and there is no PIO support anywhere in Blockly or the simulator on this board.


4. Compiler Settings & IDE Properties

When targeting this board, the compiler utilizes the following parameters:

  • FQBN: rp2040:rp2040:rpipico2w
  • Default Flashing Baud Rate: 115200
  • Flash Mode / File Type: uf2
  • Flash Memory Offsets: { bootloader: 0x0000, partitions: 0x0000, app: 0x0000 }
  • Programming Runtimes: Supports C++ (Arduino) and MicroPython.

5. Supported Blockly Board Blocks

Drawing the blocks…

6. Simulator and Flashing Diagnostics

  • Simulator: Like the plain Pico 2 (Section 3.14), this board runs on OMS's micropython-wasm engine, not a real rp2040js/CYW43439 instruction-set emulator — there is no cycle-accurate RP2350 or wireless-radio emulation in OMS. Standard digital/analog/PWM functions and the onboard LED are modeled at a behavioral level; WiFi blocks work against OMS's simulated network stack, not a real radio.
  • Flashing Guide:
    1. Unplug the USB cable from the Pico 2W.
    2. Press and hold the white BOOTSEL button.
    3. Reconnect the USB cable, then release BOOTSEL.
    4. The board mounts on your computer as a storage drive named RPI-RP2.
    5. Click Flash in OMS. The IDE compiles and saves the .uf2 file directly to the drive, which auto-unmounts and launches your code.

7. Communication Buses & Electrical Capabilities

Beyond the per-pin table above, here's the board's bus-level capability summary (from its own capabilities config, identical to the plain Pico 2):

BusDetails
UART2 hardware buses — UART0 on GP0(TX)/GP1(RX), UART1 on GP4(TX)/GP5(RX).
I2CDefault bus on GP4 (SDA) / GP5 (SCL).
SPIDefault bus: MISO GP16, CS GP17, SCK GP18, MOSI GP19.
1-WireNo dedicated 1-Wire hardware peripheral on this chip — sensors like the DHT11 are supported by bit-banging the protocol on any regular digital pin.
Analog (ADC)3 channels (GP26–GP28), 12-bit resolution (0–4095), no hardware DAC.
PWMAvailable on every GPIO pin, up to 150 MHz clk_sys-derived timing.
WirelessWi-Fi (802.11n, 2.4 GHz) + Bluetooth 5.2/BLE via CYW43439, same module as Pico W.

Electrical limits: max 12 mA per pin, max 300 mA total across all pins combined. Operating voltage range 1.62V–3.63V, nominal 3.3V.


8. Further Reading


Raspberry Pi Pico 2W (RP2350 + CYW43439) — OMS Parts