ESP32-C3 DevKitM-1

The ESP32-C3 DevKitM-1 is a compact, low-power board built on the open-source RISC-V architecture, designed as a modern, secure replacement for the legacy ESP8266.

ESP32-C3 DevKitM-1

At a glance

Pins and properties exactly as the circuit editor and simulator define this part. The text below explains how to use them.

Board facts

Board facts
FactValue
Operating voltage3.3 V
FamilyEspressif
Python runtimemicropython
Wi-FiYes
BluetoothYes
Native USBYes

Pinout

Pinout of the ESP32-C3 DevKitM-1. Select a label to see that pin in the table below.

Pins (30)

Pins of this board
PinKindFeaturesAlternate functions
GNDGround
3V3Power3.3V
3V3Power3.3V
GPIO2GPIOPWM, ADCPWM, ADC1, MISO, SPI
GPIO3GPIOPWM, ADCPWM, ADC1
GNDGround
RSTSpecialRESET
GNDGround
GPIO0GPIOPWM, ADCPWM, ADC1
GPIO1GPIOPWM, ADCPWM, ADC1
GPIO10GPIOPWMPWM, CS, SPI
GNDGround
5VPower
5VPower
GNDGround
GNDGround
GPIO21GPIOPWMPWM, TX0, UART0
GPIO20GPIOPWMPWM, RX0, UART0
GNDGround
GPIO9GPIOPWMPWM, SCL, I2C
GPIO8GPIOPWMPWM, SDA, I2C
GNDGround
GPIO7GPIOPWMPWM, MOSI, SPI
GPIO6GPIOPWMPWM, SCK, SPI
GPIO5GPIOPWMPWM
GPIO4GPIOPWM, ADCPWM, ADC1
GNDGround
GPIO18GPIOPWMPWM
GPIO19GPIOPWMPWM
GNDGround

The ESP32-C3 DevKitM-1 is a compact, low-power board built on the open-source RISC-V architecture, designed as a modern, secure replacement for the legacy ESP8266.


1. Hardware Specifications

  • Processor: Single-core 32-bit RISC-V processor core running at 160 MHz.
  • Logic Level: 3.3V. All pins operate on 3.3V logic.
  • Memory Limits: 4 MB Flash, 400 KB SRAM.
  • Wireless: Integrated 802.11 b/g/n Wi-Fi and Bluetooth v5.0 / BLE.

2. Detailed Pinout & GPIO Map

Below is the physical-to-code mapping table for the ESP32-C3 DevKitM-1 (15 GPIO pins total):

Physical Pin LabelGPIO IDPin TypePin Functions / MappingsWarnings & Cautions
D00Analog / GPIOADC1_CH0General purpose pin.
D11Analog / GPIOADC1_CH1General purpose pin.
D22Analog / SPIADC1_CH2, SPI MISODefault SPI Master In Slave Out pin.
D33Analog / GPIOADC1_CH3General purpose pin.
D44Analog / GPIOADC1_CH4General purpose pin.
D55DigitalGPIOGeneral purpose pin — no SPI/ADC function on this specific pin.
D66Digital / SPISPI SCKDefault SPI Serial Clock pin.
D77Digital / SPISPI MOSIDefault SPI Master Out Slave In pin.
D88Digital / I2CI2C SDADefault I2C Serial Data pin.
D99Digital / I2CBOOT strap, I2C SCLWired to the physical BOOT button and the default I2C clock line — must pull low to flash, so avoid wiring an I2C device here if you also need to enter flashing mode by hand.
D1010Digital / SPISPI CSDefault SPI Chip Select pin.
D1818DigitalGPIOGeneral Purpose Input / Output.
D1919DigitalGPIOGeneral Purpose Input / Output.
RX020DigitalConsole RXConnected to the USB Serial/JTAG controller.
TX021DigitalConsole TXConnected to the USB Serial/JTAG controller.

[!NOTE] There is no onboard NeoPixel/WS2812 RGB LED on this board — only a plain, non-addressable red power LED. GPIO2 is the SPI MISO pin, not an RGB LED pin. Real ESP32-S2/S3 DevKit boards do have an onboard NeoPixel; the C3 DevKitM-1 does not.

Native USB (D-/D+) is routed through this chip's USB Serial/JTAG controller rather than a conventional CP2102/CH340 bridge chip, but OMS's own board model doesn't tag any specific pin with a native-USB capability.


3. RISC-V Core & Hardware Features

  • RISC-V Architecture: Built on a single-core open ISA 32-bit RISC-V microcontroller. It contains no proprietary ARM or Tensilica code pipelines, offering high instruction execution speed at minimal battery draw.
  • No Cap-Touch Support: Unlike the LX6/LX7 cores (ESP32 / S2 / S3), the RISC-V ESP32-C3 die does not contain hardware capacitive touch circuitry. board_read_touch returns nothing usable on this board.
  • No Hardware DAC: Like the ESP32-S3, this chip has no onboard DAC — board_analog_out always falls back to a PWM approximation here.

4. Compiler Settings & IDE Properties

When targeting this board, the compiler is intended to use the following parameters:

  • FQBN: esp32:esp32:esp32c3
  • Default Flashing Baud Rate: 921600
  • Flash Mode / File Type: esp
  • Flash Memory Offsets: { bootloader: 0x0000, partitions: 0x8000, app: 0x10000 }
  • Programming Runtimes: Supports C++ (Arduino) and MicroPython.

[!WARNING] Known bug: same issue as the ESP32-S2/S3 (Sections 3.6/3.7) — this board's actual internal id (esp32c3) doesn't match any key in the compiler's board-config lookup table (which only has hyphen/underscore forms like esp32-c3), so compiling currently silently falls back to plain ESP32's FQBN (esp32:esp32:esp32) instead of the C3-specific one above. See Known_Bugs.md §2.0.


5. Supported Blockly Board Blocks

Drawing the blocks…

6. Simulator and Flashing Diagnostics

  • Simulator: Core timers and digital logic run locally.
  • Flashing Guide: The ESP32-C3 features a built-in USB Serial/JTAG controller, enabling flashing directly over USB without external bridge chips. Connect USB, click Connect Serial, and upload. If the connection fails, press and hold the BOOT (GPIO 9) button, tap the RESET (EN) button, and release BOOT to force download mode.

7. Communication Buses & Electrical Capabilities

Beyond the per-pin table above, here's the board's bus-level capability summary (from its own capabilities config):

BusDetails
UART1 hardware bus — TX on GPIO21, RX on GPIO20, shared with the USB programming port.
I2CDefault on D8 (SDA) / D9 (SCL) — note D9 is also the BOOT strap pin.
SPIDefault on MOSI D7, MISO D2, SCK D6, CS D10.
1-WireNo dedicated 1-Wire hardware peripheral. Sensors like the DHT11 bit-bang the timing on any regular digital pin instead.
Analog (ADC)5 ADC-capable pins (D0–D4), 12-bit resolution. No hardware DAC, no touch.
PWMEvery GPIO pin on this board is PWM-capable (6 LEDC channels, 14-bit resolution, up to 40 MHz).

Electrical limits: max 40 mA per pin, max 1000 mA total across all pins combined (per the ESP32-C3 datasheet's absolute maximum ratings).


8. Further Reading


ESP32-C3 DevKitM-1 — OMS Parts