Thermistor (NTC)

An NTC (Negative Temperature Coefficient) Thermistor is a thermally sensitive resistor whose resistance decreases exponentially as temperature increases.

Sensors11 blocksMicroPythonC++
Thermistor (NTC)

At a glance

Pins and properties exactly as the circuit editor and simulator define this part. The text below explains how to use them.

Pinout

Pinout of the Thermistor (NTC), drawn as in the circuit editor. Select a label to see that pin in the table below.

Pins

Pins of this part
PinLabelType
11Signal in
22Signal in

Properties

What you can change in the Property Inspector.

Properties of this part
PropertyRange or choicesDefault
Type10kΩ NTC (B=3950K) — most common, 100kΩ NTC (B=4250K), 1kΩ NTC (B=3380K)10kΩ NTC (B=3950K) — most common
Temperature-40 to 150 °C25 °C

An NTC (Negative Temperature Coefficient) Thermistor is a thermally sensitive resistor whose resistance decreases exponentially as temperature increases. In Open Maker Studio, thermistors are wired in a voltage divider to measure temperature.


1. Schematic Symbol

Standard temperature-dependent resistor symbol — a resistor with a diagonal line through it, labeled t°:

t° 1 2

2. Hardware Specifications

  • Nominal Resistance (R25R_{25}): The resistance of the thermistor at 25°C. OMS models 3 real named presets:
    • 10kΩ NTC (Beta β=3950\beta = 3950K) — default and most common.
    • 100kΩ NTC (Beta β=4250\beta = 4250K) — often used in 3D printer hotends.
    • 1kΩ NTC (Beta β=3380\beta = 3380K).
  • Pins: 2 non-polarized passive terminals.

3. How it Works & Mathematical Formula

To measure temperature, the thermistor is connected in a voltage divider with a known fixed resistor (typically matching the nominal R25R_{25} value, e.g., 10 kΩ10\ \text{k}\Omega).

[!IMPORTANT] Wiring Orientation: The formula below assumes the thermistor is connected between the ADC pin and GND (bottom of the voltage divider), with the fixed series resistor between VCC and the ADC pin. If your wiring is reversed (thermistor to VCC, series resistor to GND), swap the ratio: use ADCraw/(ADCmax−ADCraw)ADC_{raw} / (ADC_{max} - ADC_{raw}) instead.

The resistance of the thermistor (RR) is calculated from the raw analog reading:

R=Rseries×(ADCmaxADCraw−1)R = R_{series} \times \left( \frac{ADC_{max}}{ADC_{raw}} - 1 \right)

Using the Steinhart-Hart Beta-Parameter Equation, the temperature (TT, in Kelvin) is calculated as:

1T=1T0+1βln⁡(RR25)\frac{1}{T} = \frac{1}{T_0} + \frac{1}{\beta} \ln\left(\frac{R}{R_{25}}\right)

Where:

  • T0=298.15 KT_0 = 298.15\text{ K} (25°C in Kelvin).
  • R25R_{25} is the nominal thermistor resistance at 25°C.
  • β\beta (Beta) is the material constant of the thermistor.
  • To convert Kelvin to Celsius: TCelsius=T−273.15T_{Celsius} = T - 273.15.

4. Component Properties (Property Inspector)

When you select the Thermistor on the canvas, you can modify the following parameters in the Property Inspector panel:

  • Temperature (temperature): Simulates the ambient temperature surrounding the thermistor.
    • Default: 25 °C
    • Range: -40 °C to 150 °C (step size 1 °C)
  • Type (model): Selects the thermistor's R25/Beta preset.
    • Default: NTC_10K (10kΩ, β=3950)
    • Options: NTC_10K, NTC_100K, NTC_1K

There's no separate "Series Resistor" component property — that field only exists on the sensor_thermistor_read_celsius Blockly block (Section 5 below), as a plain number input, not a property of the simulated thermistor part itself.


5. Supported Blockly Blocks

Drawing the blocks…

6. Simulator Behavior

  • On-Canvas Drag Slider: The component renders its own draggable temperature slider directly on the canvas graphic (in addition to the Property Inspector's Temperature control) — drag it during simulation to heat up or cool down the thermistor in real time.
  • Real-time Resistance Readout: While a simulation is running, OMS renders a live text overlay on the component showing its current resistance — not a hover-only tooltip, always visible whenever there's meaningful current through it. The underlying resistance is recalculated continuously from the real exponential β-parameter model as you change temperature.
Thermistor (NTC) — OMS Parts