Zener Diode

A Zener diode is a specialized diode designed to conduct safely in reverse once its rated Zener voltage is reached, deliberately clamping the voltage across it — the basis of simple shunt…

Zener Diode

At a glance

Pins and properties exactly as the circuit editor and simulator define this part. The text below explains how to use them.

Pinout

Pinout of the Zener Diode, drawn as in the circuit editor. Select a label to see that pin in the table below.

Pins

Pins of this part
PinLabelType
ANODEASignal in
CATHODEKSignal out

Properties

What you can change in the Property Inspector.

Properties of this part
PropertyRange or choicesDefault
Zener Voltage3.3V (3V3), 5.1V (5V1), 6.2V (6V2), 9.1V (9V1), 12V (12V), 15V (15V)5.1V (5V1)
Power Rating0.25W, 0.5W, 1W0.5W

A Zener diode is a specialized diode designed to conduct safely in reverse once its rated Zener voltage is reached, deliberately clamping the voltage across it — the basis of simple shunt voltage regulators. In Open Maker Studio, it does not have Blockly code blocks — it interacts directly with the real-time SPICE analog simulator.


1. Schematic Symbol

Standard Zener symbol — a diode triangle with a bent (Z-shaped) cathode bar:

A K

2. Real Part Family & Characteristics

OMS's Zener Diode is calibrated against the real 1N4728A–1N4744A 1W Zener family (Vishay datasheet), with 6 selectable real voltages: 3.3V (1N4728A), 5.1V (1N4733A), 6.2V (1N4735A), 9.1V (1N4739A), 12V (1N4742A), and 15V (1N4744A). Forward operation behaves like a normal diode; once reverse-biased past its rated Zener voltage, it clamps the voltage across it instead of breaking down destructively — this is the whole point of the part.


3. Core Calculations & Math

  • Max Safe Current: given the package's power rating and the selected Zener voltage:

    $I_{max} = \frac{P_{rating}}{V_z}$

This is the exact formula OMS uses for its real-time overcurrent fault threshold (see Section 6) — as $V_z$ increases, the safe current drops for the same power rating.

4. Component Properties (Property Inspector)

When you select a Zener Diode on the canvas, you can modify the following parameters in the Property Inspector panel:

  • Zener Voltage (zenerVoltage): Selects the real regulation voltage.
    • Default: 5.1 V
    • Options: 3.3 V, 5.1 V, 6.2 V, 9.1 V, 12 V, 15 V
  • Power Rating (powerRating): Sets the package's power dissipation rating, used to compute the max safe current above.
    • Default: 0.5 W
    • Options: 0.25 W, 0.5 W, 1 W

5. Programming Notes

Zener diodes are purely passive analog components and have no associated Blockly blocks. A Zener regulator only influences the electrical behavior of connected components — for example, a Zener-clamped reference rail determines the voltage a board_analog_read block reads downstream.


6. Simulator Behavior

  • Real-time Current Readout & Regulation Label: While a simulation is running, OMS shows the current through the Zener and labels its state CLAMPING whenever it's actively regulating (reverse voltage above ~90% of VzV_z, drawing meaningful current) — the body also glows while clamping cleanly.
  • Overstress Fault: exceeding both 130% of the rated Zener voltage AND meaningful current (not just one or the other) triggers a real OVERCURRENT fault, using the Prating/VzP_{rating}/V_z formula from Section 3 as its threshold — recoloring the diode and showing a warning, with a message suggesting a series current-limiting resistor.
Zener Diode — OMS Parts